Wednesday, 24 July 2019

Sail Trimming Tips

This aim of this article is to provide you with a few tips to help optimise your sail trim and get the best out of your sails. As with all trim and tuning guides, this is just that, a guide. This information should not be taken as absolute. It is impossible to sail strictly by the numbers. Trim and tune are dynamic, requiring constant changes to get the most from the boat. It is more important to understand the concepts behind tuning, and the effects of the different controls so that you can learn how to shift gears. Keep an open mind and experiment in changing conditions to determine the right combination for the moment, or simply what works for your sailing style. There is no one way to make your boat go fast. The single most important thing is to recognise when you are slow and to do be prepared to do something about it.


Upwind Trim: Headsails

Most race boats will carry at least 2 headsails to cover the wind range but some boats will certainly carry 3 or 4. On modern boats with non-overlapping rigs the Code 1, Code 2 and Code 3 Jibs will all be more or less the same size. They will however differ considerably in shape and weight to accommodate different wind speeds. On a more traditional boat with overlapping headsails the differences are a little more obvious as the sails will differ in area quite considerably from one another. Within this guide I will not endeavour to provide tips for each sail, but will consider the basic tools that the trimmer has at his disposal for any headsail.

Increasing halyard tension pulls the
camber in the sail forwards
1.        Halyard: Every sail will have been designed with its position of maximum camber and entry angle placed optimally for its anticipated wind range, the boats characteristics, expected headstay sag and materials used. A sail is used across a range of conditions so it is necessary to adjust the shape of the sail to suit. Put simply, increasing halyard tension pulls the camber forwards and flattens the sail, and easing the halyard lets the draft go aft with the sail getting a little deeper.

The basic rule is to use enough halyard tension to just smooth out the wrinkles in the luff. In light airs it is better to have slightly too little tension than too much. This makes the entry finer which will help with pointing, and will also power up the back of the sail. As the breeze increases, you need to use more halyard tension. This will round up the entry which makes the steering groove wider, and will also flatten the exit of the sail, which in turn de-powers it. Care should be taken with the No.3 jib as insufficient halyard tension and/or excessive forestay sag will result in the sail being ‘too round’ which produces excess drag causing the boat to heel over. Using lots of halyard tension helps to prevent this. It is vitally important that your jib halyard is marked so that you can easily re-produce fast settings. Care should be taken not to use wrinkles on the luff or a mark on the forestay as the guide to halyard tension. Instead, the trimmers should use the camber stripes in the sail as the main point of reference. Note that as a sail ages it will typically shrink in the luff and stretch in the leech which means that the camber in the sail will gradually creep aft. This in turn will mean that more halyard tension will be required to hold the draft forwards as the sail ages.
2.       Sheet Tension: the genoa sheet is perhaps the most important headsail control and must be played constantly, easing to accelerate, trimming to point. Sheet tension will change with every change in wind speed, but the basic premise is to trim as hard as possible without slowing the boat down. Remember speed first, then point. Adjustments are not as frequent in steadier breeze, but the sheet still needs to be adjusted for changes in wave patterns or to duck other boats. Sails can be sheeted harder in flat water than they can be in lumpy seas for the same windspeed. If you are fast sheet harder, if you are slow, try easing it slightly. In light airs the genoa trimmer should be sat to leeward, and should be constantly monitoring the shape of the genoa relative to the speed of the boat. Use the spreaders and shroud base as reference points so that known fast settings can be reproduced. Again, as the windspeed increases, so will sheet tension. On boats with overlapping sails do not be afraid to have the foot of the genoa touching the shroud base, but the leech should not ever touch the spreader tips.

3.   Lead position: The base setting for the jib lead should apply roughly equal tension to the foot and the leech of the jib, i.e. an imaginary extension of the sheet through the sail would roughly bisect the luff. The standard method for determining the median sheet lead position is to luff up slowly and watch the luff of the sail. It should luff at about the same time from top to bottom. If the top breaks too early, and the bottom of the sail is strapped to the shrouds, then the lead needs to be moved forward. If the foot of the sail is very round and well off the shrouds, while the top is in close to the spreader, the lead should be moved aft. Close attention therefore needs to be paid to the leech profile of the sail as well as what is happening at the luff. If the car is too far forwards the leech will be too tight and the bottom of the sail too full; as well as being slow this will cause unnecessary backwinding. Similarly, if the car is too far aft, the foot of the sail will be tight but without sufficient leech tension.
Base lead position applies roughly equal tension to leech and foot
The lead should be moved aft as the sail is sheeted in harder and operates closer to the top of its range. In light conditions, as the sheet is eased, the lead will need to move forward. A useful rule of thumb is that if you are needing to drop the traveller to keep the boat on its feet, then move the lead aft. Similarly, if the genoa is trimmed in normally, the main has been flattened, and there is still excessive backwinding, move the lead aft. Basically, as you become over powered, move the lead aft, and do not worry if the top tell tales don’t fly properly as you open the leech up. If your jib is trimmed so that the whole sail is working, but the mainsail is flogging to keep the boat on its feet, ease the jib. Give away the top of the sail to balance the boat allowing both sails to do some luffing.

4.     Forestay Tension: In light conditions you will need more forestay sag to make the genoa fuller and this is achieved through easing the forestay if that is possible, or easing the overall rig tension if possible, or making sure that the backstay is eased, mainsail trim permitting - see below. Similarly, in heavy conditions the rig is tightened helping to prevent forestay sag. This de-powers the jib and helps pointing.
Tightening the forestay flattens and depowers the sail

Upwind Trim: The Mainsail

Mainsail trim has two primary goals. First, balancing speed versus pointing by controlling the twist or how open the leech of the mainsail is. Second, keeping the right amount of overall power, helping to maintain a constant angle of heel and the right amount of weather helm. This section will address adjustments to mainsheet, traveller, outhaul, halyard, cunningham, vang and backstay.

1.        Mainsheet: like the jib sheet, there is no one magic setting for the mainsheet. It should be adjusted continually with each change in wind speed and/or wave pattern. Basically, increasing mainsheet tension reduces twist and tightens the leech, which makes the boat point, but also slows it down. Easing the sheet induces twist, which accelerates air flow across the sail. This allows the boat to bear away and accelerate. Initially, the main should be sheeted until the aft section of the top batten is parallel to the boom. Check this by looking up the sail from underneath the boom (see picture below). This is the ‘default’ or base position and at this point the top tell tale will be on the verge of stalling but should be flying about half of the time. Once the boat is upto speed, increase sheet tension until the boat starts slowing. Remember, speed first then pointing. The art is to find the delicate balance between speed and pointing, always trying to trim as hard as possible without giving away too much speed.
Base position with aft end of top batten parallel with boom
In light air, the sail will be eased and twisted from the base position. In moderate air the sail will be sheeted hard with the top batten at least parallel. In heavy air the sail should be sheeted as hard as the angle of heel will allow. Bear in mind that in choppy seas, more twist is required to keep the boat moving, and on flat water you need harder leeches for pointing.
Above: flatter sail with more twist. Note the top batten
is falling to leeward below the line of the boom. 
More leech tension creates a more powerful sail with the top
batten being pulled above the line of the boom. Be careful
not to stall the sail in this situation













2.      Traveller: the traveller serves two functions. Firstly, it controls the booms position relative to the centreline of the boat, and secondly it helps to steer the boat by controlling the helm and angle of heel in the puffs and lulls. To position the boom, set the twist with the mainsheet and use the traveller to put the boom on the centreline for maximum power and pointing. In light air the mainsheet will be eased to promote acceleration and keep the leech open and the traveller will be well to windward to keep the boom close to the centreline without too much downward pull from the mainsheet. In moderate conditions small adjustments will be necessary to control helm balance. It is important to dump the traveller quickly when a gust hits and you begin to get over powered, but equally important to pull it back on again as soon as the heel is controlled or the gust has passed. Wait too long and you have missed the opportunity to point once the boat has accelerated. As the wind speed increases the average position of the traveller will be slightly further down the track. In over about 18 knots of breeze you may need to ease a little mainsheet as well. However, before you ease mainsheet in windy conditions you may want to have the vang pulled on hard in order to prevent giving the whole leech away. Think of the traveller as the ‘tip meter’ once the mainsheet has been set for twist. The traveller position should be monitored continually and may need to be adjusted with every change in heel or any time the mainsheet is adjusted. 

The big question is whether to dump the traveller or mainsheet in the gusts or as it gets windier. Well both will work. The first school of thought says that easing the traveller down the track in the gusts means that all leech tension is maintained and therefore the boat will continue to point. The downside to this approach is that the slot between the mainsail and genoa becomes choked, the mainsail backwinds, and the sail plan loses efficiency. The second school of thought which counters this is that instead, the mainsheet should be eased slightly in the gusts which will enable the top of the sail to twist off thus depowering the it (and keeping the boat on its feet) but because the traveller is still well up the slot remains open and the tension in the lower leech will keep the boat pointing anyway. The trick is to work out what works best for you and your boat. One rule of thumb though is that if you feel you have to ease the traveller, the mainsail should be fully flattened and depowered via the other controls (see below) before you get to that point in order to minimise backwinding. If you end up in a situation where the whole sail is ragging wildly then something is wrong; there is no reason why the sail should be flogging with correct trim and set-up! For more subtle changes in wind speed it may be better to use small adjustments to the traveller to fine tune the helm. In the big gusts dumping the mainsheet will get the boat back on its feet more quickly but be sure to get it back on as soon as possible.
3.       Vang: the vang is primarily an offwind control. It takes over the job of pulling down and providing leech tension when the boom is eased out and the mainsheet is no longer controlling the twist. However, upwind, certainly on smaller boats the vang can be used to help out the mainsheet with the job of pulling down the boom and maintaining leech tension. If the vang is hard on, the mainsheet can be eased in big gusts without giving up too much of the leech . In light air make sure the vang is off using only enough tension to stop the boom from bouncing. In heavy air it will be necessary to ease the vang at the weather mark to assist with bearing away. Easing the mainsheet may not be enough.

4.       Luff tension (halyard and cunningham): halyard and cunningham both tension the luff. Initial luff tension should be just enough to smooth out the wrinkles in the front of the sail. Leave a few wrinkles in the bottom third of the sail in light to moderate air. As the breeze increases more luff tension is required to prevent the draft in the sail from moving aft. Use the halyard first, and when the sail is at the black band use the cunningham. Do not under estimate the usefulness of the cunningham, it is one of the primary sail controls that many people choose to ignore. As soon as the boat is overpowered start pulling the cunningham on hard upwind. It is easier to adjust and fine tune the cunningham when sailing than the halyard. As with the headsails, as the sail ages the camber will creep aft so more luff tension will be required to keep the draft in the correct place. Use the camber stripes as a guide.

5.       Outhaul: the outhaul controls the depth in the lower third of the mainsail. If you need more helm and feel, ease the outhaul. Power in the bottom of the main will increase weather helm. In very light airs (less than 5 knots) the outhaul needs to be pulled out fairly firmly in order to prevent flow separation in the lower part of the mainsail. If the sail is too full in these very light airs it will stall. In 5-12 knots the outhaul can be eased slightly to increase power. Once the boat is fully powered with all the crew hiking (normally about 10-12 knots of wind) the outhaul should be maxed out. The outhaul should be eased  when running but be careful not to overdo it, when trying to run deep you may find that having the additional maximum projected area associated with a slightly soft foot is faster than having a really deep sail, I prefer to ease slightly more than is sufficient to remove any crease across the foot from its upwind setting. The outhaul should be eased for power when reaching (unless of course you are over powered!). Make sure that you have the outhaul calibrated so that you can repeat known fast settings (make sure all sail controls are calibrated for the same reason!)

6.       Backstay: On a boat with a fractional rig increasing the backstay tension does two things. Firstly, as the mast bends the upper two thirds of the mainsail flattens out and the leech opens up, thus de-powering the sail. Secondly, the headstay gets tighter (providing you have set up the pre-bend correctly to prevent over-bending), which prevents headstay sag, which in turn prevents the jib from getting too full as the breeze increases. On a masthead rigged boat, increasing the backstay tension is unlikely to bend the mast much but will have a bigger effect on the forestay. 

Broadly speaking as the breeze increases you will need more and more backstay. However, even in very light airs you may need to use a little backstay in order to help the mainsail leech to stay open. Since adjusting the backstay has a large and immediate effect on mainsail leech tension, main sheet tension needs to be adjusted at the same time. Bending the mast opens the leech, so you will need to add mainsheet as you add backstay, and ease mainsheet as you let the backstay off. You will also need to adjust the traveller accordingly.


Pre-bend and mainsail shape

The 'pre-bend' in the mast, or initial bend without backstay needs to be in harmony with the luff curve that has been built into the mainsail. If the mainsail flattens out too quickly (as characterised by overbend wrinkles running diagonally from clew to mid-mast before the backstay is maxed out), then you need tighter lowers and/or a shorter headstay to reduce bend and make the mainsail fuller. In heavy air you should be able to pull the backstay all the way on just before the overbend wrinkles appear.

If the mainsail is too full for the amount of backstay being used, as characterised by excessive backwinding, or a sail which is ‘knuckled’ and excessively round at the front, less lower tension and/or a longer headstay is necessary. Once the mast has been set with the correct forestay length and shroud tensions for medium air, these should be regarded as ‘base’ settings. In very light air decrease the tension on the lowers and add headstay length to induce additional pre-bend. Extra pre-bend and softer rig tension will also increase headstay sag creating more power in the genoa, which will also make it easier for the helmsman to ‘feel’ the boat and stay in the groove.

The uppers (cap shrouds) should not generally need to be adjusted much providing you have an adjustable forestay. The upper diagonals (D2’s) again should not need to be adjusted, but bear in mind that these also act as a control for mast bend. If the sail is too full in the upper sections, they may be too tight, and vice versa.

As a general guideline, in light airs ease the overall rig tension on the forestay and/or decrease the tension on the lowers to induce additional pre-bend. As the breeze builds, increase the overall rig tension to prevent the mast from overbending as the backstay is pulled on. You should aim to create a tuning grid similar to the example below.


0-7 knots
8-15 knots
16-22 knots
23+ knots
Lower Tension
Ease 1 turn
Base
Base
Tighten 2 turns
Forestay Tension
Ease 5-8 turns
Base
Tighten 5 turns
Tighten 8 turns from base

Downwind Trim

The key to running effectively is to project as much area to windward as possible away from the mainsail, thus facilitating sailing deep. Do not get pre-occupied with having the clews at the same height as depicted by most sailing guides. You should start by altering the pole height so that the luff of the sail isn’t breaking too high or too low. You should then set the leech accordingly by using the tweaker lines. Pulling the tweakers on will stabilise the spinnaker when it is windy but don’t overdo it or the sail will stall. Use the centre seam as a guide to trim, which should be approximately perpendicular to the horizon. If it feels right it probably is right. The main thing when sailing downwind is to make sure the spinnaker is pressured up all the time. The trimmer and helmsman should be talking to each other continually so that the helmsman can get the boat really low when he has pressure and he doesn’t sail too high when he needs more pressure. Easing the vang and twisting the mainsail will also help you get deep, but at the same time it will make the boat more unstable and less forgiving. Be prepared to adjust the vang continually downwind and sail where you are comfortable. Sailing downwind is at least as tactical as sailing upwind with huge gains to be made by sailing at the right angles on the right shifts. If you tack on shifts going upwind you should gybe on them going downwind.

The crew should be well forward in light air, gradually moving aft and to weather as the breeze builds. The boat should ideally be heeled slightly to weather when going downwind which helps to project the spinnaker and helps the boat to drive off in the puffs. Weight should be shifted to stabilise the boat and promote surfing in heavy air. When it is breezy all the crew should be well aft, with one person being allocated as ‘vang man’ to de-power and power up the main as necessary.

Miscellaneous Tips

1.       Crew weight upwind: sail with a constant angle of heel, and with as little weather helm as you can stand. Generally this will mean sailing as flat as possible. In light air the weight should be to leeward and forward to induce feel and helm. In less than 5 knots of breeze it pays to put a couple of crew members down below particularly in sloppy conditions when it will help prevent pitching. Once the boat is powered up all the crew should be hiking hard and be bunched together around the maximum beam. Again keeping the crew weight together helps to reduce pitching.

2.       When the boat starts getting overpowered don’t fight the helm. Instead, ‘feather’ the boat slightly by sailing ‘inside’ the jib tell tales allowing the windward ones to lift slightly to keep the boat on its feet. Try to focus on steering to a consistent angle of heel. In other words don’t get pre-occupied with keeping the tell tales on either side of the sail streaming together.


3.       Don’t be afraid to pull control lines really hard! One of the most common mistakes that we see is things like the backstay not being pulled on anything like hard enough to depower the main or the mainsheet not being pulled on hard enough to get the boat to point!

4.       Remove all unnecessary items of kit from the boat. Encourage the crew to bring only what they are going to wear. You don’t need to have a pair of boots and a pair of shoes on the boat for example. Stow any spare kit, fenders etc over the keel.

5.       Make sure the bottom is clean and smooth. If the boat is anti-fouled, this should be rubbed flat with increasingly fine wet and dry paper. Do not under estimate how detrimental even a little bit of slime or weed can be to boatspeed. Being conservative we might say that having a dirty bottom will slow you down by 0.2 of a knot. This doesn’t sound much but it equates to 400 yards an hour. In a two hour race this is nearly half a mile!

6.       Make sure that all sail controls are visibly calibrated so that you can repeat known fast settings. This includes halyards and sheets.

7.       Similarly, put marks on the spinnaker pole controls so that you can pre-set it accurately before hoisting.

8.       Put a cover over the jib halyard at the point where it goes through the jammer. Maintaining halyard tension is vital when it is windy and most halyards will gradually slip as you progress upwind. Alternatively, keep the genoa halyard on the winch until you approach the windward mark.

9.       Keep an open mind and do not be afraid to experiment. Perhaps the most important point to recognise is when you are slow, and then to do something about it!

10.    Have fun!

Wednesday, 20 June 2018

Construction styles in contemporary sailmaking

It is fair to say that sailmaking has probably changed more in the last 15 years or so than at any time in the past. Buying new sails can be something of a bewildering experience; speak to 3 or 4 different sailmakers and you could easily end up with what appears to be literally dozens of different cloth options and construction styles to choose from. However, a little knowledge can simplify the process considerably. The aim of this article is to provide a brief account of the three generic construction types that most sailmakers would currently offer.

1. Cross-Cut. In most instances cross-cut sails, where the panels run roughly horizontally across the sail would be made from woven Polyester, commonly known as Dacron. These are traditionally associated with cruising boats but are also commonplace on many smaller race boats and of course on dinghies.

Dacron sails are woven in the age old way on a special loom and have fibres running in a ‘warp’ and a ‘weft’ (fill) direction. The warp fibres run in a continuous length along the roll whilst the fill fibres run perpendicular to the warp, i.e. directly across the roll. It is possible to vary the quality and size of the fibres as well as the density of the weave and this in turn results in Dacron’s with different properties. In fact all of the cloth manufacturers offer many different styles of Dacron, each of which is suited to a different end use or budget. As a result, all Dacron's are not created equal, so it is really important to err on the side of quality and to make sure that the particular style of cloth that is proposed is actually suited to the end use. High aspect sails, typically Mainsails and blade Jibs need cloth that has a different set of stretch characteristics to that used on an overlapping furling genoa. Get it wrong, or compromise on quality and the consequences can be dire!

Dacron fabrics tend to be much stronger in the ‘fill’ direction than the ‘warp’ direction which is why they are used in cross-cut applications; the strong fill fibres are lined up so that they correspond with the chord between head and clew which is roughly the direction of the highest loads in the sail (see the red line in the picture below). However, this depiction of the loads in the sail is rather simplistic as there are additional loads running in many other directions that are not particularly well catered for by simple woven fabrics.

2. Radial Cut. In order to cater for the myriad of loads present in a sail, the sailcloth manufacturers developed cloths that were stronger in the warp direction than the fill direction (opposite to Dacron) and which also had better properties in the ‘bias’ (45 degree) direction. By using these cloths in a tri-radial panel orientation more of the loads in the sail could be supported. The resulting improvement to shape stability means better performance. It is important to note that this is as important to the cruising sailor as the racing sailor as better shape retention equates to less heeling, less flogging and better handling. In the graphic below it is easy to see how the loads in the sail (red and blue lines) are more effectively taken up by the radial panel orientation on the right of the graphic than the cross cut one.

The cloths themselves are usually laminates featuring load bearing fibres sandwiched between clear Mylar films. There are a variety of fibre types used including Polyester, Pentex, Twaron, Technora, Dyneema and Carbon, each of which would be more or less suited to a particular size of boat, budget and end use. Adding a single or double sided taffeta backing to the fabric makes them more durable (though heavier) and therefore better suited to cruising.

An alternative to laminate sailcloth for radial constructions is a range of woven fabrics commonly known as Dyneema & Polyester 'hybrids'. These include 'Hydranet' from Dimension Polyant and 'Fibrecon Hybrid' from Contender Sailcloth. These hybrids offer much better shape stability (and hence performance) than the Dacron alternatives due to the inclusion of high modulus Dyneema fibres in the weave, whilst offering better durability than the laminates. 

3. Membrane constructions. This effectively refers to sails that are made from their base components upwards rather than cut from cloth that is on a roll. They are completely custom products in that typically each panel of the sail is laminated individually with a custom complex fibre map that is designed with the particular boat and end use in mind. The panels are then joined together to create one homogenous structure. The resulting fibre arrays more closely mimic the anticipated sailing loads than even the tri radial sails offering further improvements to shape stability and hence performance. Although these membrane sails were initially used solely on race boats, they are now increasingly commonplace on cruising boats of all shapes and sizes as improvements to technology and construction methods have reduced costs and added to their durability making them very cost effective alternatives to their radial cut counterparts. The photo below shows a membrane panel part-way through its lamination process, note the complex fibre array.


Summary. Broadly speaking, whatever it is that you are looking to buy (or whatever it is that your sailmaker is trying to sell you) will fall into one of these three construction types, regardless of whatever name the sailmaker has given it. 

Cross cut usually means Dacron though there are some laminates available that are designed for cross cut applications. Dacron sails will be the least expensive option but will offer the least in terms of shape stability and hence performance. 

Radial cut usually means that laminated fabrics will be used. These incorporate a variety of different load bearing fibres and can be made more durable by adding a woven taffeta backing to them. Laminate sails will be more expensive than Dacron but will offer far more in the way of performance. They are not as robust as Dacron's however, although the taffeta backings do toughen them up significantly. A range of woven hybrid cloths incorporating Dyneema & Polyester mixes is available for radial cut sails. These offer the ruggedness of Dacron but with some of the performance gains associated with laminates. 

Membrane (or 'string') sails offer further advances in load distribution and hence performance and certainly shouldn't be regarded as the reserve of the racing sailor. Their custom nature means that they can be tailored to any end use. Many of them are competitively priced when compared to the radial cut alternatives. Although most sailmakers will have their own slightly different methodology for constructing their membrane sails essentially the principles remain the same. It wasn’t that long ago that laminate sails were the exclusive domain of the racing sailor but nowadays laminates including membranes featuring high tech fibres such as Carbon Fibre are routinely found on cruising boats. Next time you are looking to buy new sails don’t be afraid to explore the various options to find out what really is best for you….

Thursday, 12 October 2017

Winter Sail Care

Winterising Sails

As we approach the time of the year when most people are thinking about laying-up their boats for the winter it is important to give some thought to your sails. All too often we see furling genoas being left up all winter whilst the boat is ashore; the same goes for mainsails that are left on underneath their sail covers. This of course means that the sails are at the mercy of the elements for extended periods of time; not only that but the tightly bound and folded sails combined with a damp salty environment become perfect breeding grounds for mould and mildew. We strongly recommend therefore that if the boat is out of use for any period of time, especially over what can be a long and harsh winter at the very least they should be unbent and stored somewhere dry. If you are in a position to rinse and dry the sails yourself and inspect them closely prior to folding them away that’s great but if not we are happy to take care of the whole process for you.

Sail repairs and service by professionals


Regular maintenance of your sails by skilled sailmakers can significantly enhance their working life, saving money for the owner and ensuring reliability when it is needed most. Sails operate in a hostile environment where sail and pollutants can cause serious damage to even the best kept sails. Similarly, constant wear & tear requires careful repair and maintenance with an end of season overhaul being essential for the longevity of your sail wardrobe. It is important that any damage, no matter how small is repaired as quickly as possible in order to prevent further damage occurring.

Recuts and retrofits

A simple recut can improve shape and give a new lease of life to a ‘tired’ sail. With improved shape comes improved performance and handling, something that is well worth thinking about whilst the sail is off the boat anyway. Retrofit extras include UV protection, luff flatteners for shape retention when genoas are partially furled, changing from hanks to luff foils, altering batten configurations, adding reefs to mainsails etc.

Sail Laundry

OneSails recommend that any sails that are salty or damp get sent to a sail laundry prior to winter storage. The laundry process will remove any salt and any other airborne pollutants which may harm the sails if left for any period of time. This in turn helps to prolong the overall life of the sail. It also has the added benefit of making the sails easier to work on if any service work is required, and means that they will be dry when they are put away for the winter. If they are put away whilst damp, they are more likely to attract mould or mildew and will not be in a pleasant state when you come to bend them back on next season.

The specialist sail laundries are essentially large warehouse type buildings. The sails are cleaned by a variety of processes. A few older sails that have either gone soft with age or which have a soft feel by design get washed in large industrial washing machines. There is very little (if any) in the way of detergents or bleaches that gets added at this stage, the sails are simply rinsed to remove any salt. The vast majority of sails and in particular racing sails don’t go into the machines. They are laid flat on a smooth concrete floor and hosed down with fresh water from a pressure washer with a special attachment. Whilst the sail is on the floor any spot cleaning is done to remove any green algae, mildew, grease etc. At this stage some chemicals such as mild detergent solutions will be used where necessary. If chemicals have been used, the sails are then rinsed again. Once the sails have been cleaned they are then hung up to dry before being folded and returned to the sailmaker.

Whilst we highly recommend sail laundry for any sails that are being stored for any length of time, the process does have certain limitations. Although the sails will be returned from the laundry dry, salt free and in an ideal state to be worked on or stored, the process is not a cure all that will leave the sails looking ‘as good as new’. Stains such as mildew, grease and rust may be removed if they are treated straight away but will stain the sail permanently if left for any period of time. Other typical stains are from diesel or machine oil. These cannot be removed fully and will always leave a stain though laundering them will remove any smell and surface residue. It should also be noted that there is no guarantee that stains including mildew, mould or rust will be removed during the laundry process.

At OneSails GBR we are pleased to be able to offer a full range of sail repair and maintenance services, please feel free to contact us to see what we can do for you and how we can help to extend the life of your sails. 

Thursday, 4 August 2016

Cowes Week Sail Repair Service

We will be operating an overnight sail repair service from our Hamble loft during Cowes Week. The drop and collection point in Cowes will be the yellow doors in the ground floor ‘wet’ bar area at the Island Sailing Club (see pic below). The doors are just next to the bar and sail storage area. There should be an A4 sized OneSails sign in situ. Sails will need to be dropped between 4.00pm and 5.00pm and will be returned to the ISC between 9.00 and 9.30 the following morning. This service is strictly ‘by arrangement’, please do not leave sails unless you have spoken to the loft on 02380 458213 or Peter Kay on 07785 323345.

Friday, 4 March 2016

Springtime - bending on a furling genoa

It has got to that time of year again when boats are eagerly being polished, antifouled and readied in every other way for the new season. For some, fitting the sails back on to the boat is a straight forward enough job but for others it can be a little daunting. Here’s some tips for bending on a genoa.

First, if your sail hasn’t been serviced by a sailmaker check the sail over to make sure that there are no outstanding repairs or service issues from last season that need addressing. Check the luff tape itself for nics & tears and check that the stitching itself, particularly in areas that stay exposed such as the leech tape and webbings in the corners, isn’t rotten. You can do this by rubbing a finger nail over the stitching; if it breaks it needs to be re-sown! It will be easier to address any issues now than find out about them after the sail has been fitted!

Similarly, check that the furling gear is all working nicely, it is easier to check the top swivel before it is hoisted! If the sail has been down all winter there is a good chance that the groove in the foil has accumulated wind blown dust and salt so try and flush this through if possible with fresh water. You could even try spraying some ‘lube’ or Teflon spray into the groove and wiping this through with an off cut of a suitable sized luff tape.

Next, check that a sufficient length of the furling line is wound onto the drum and that it is wound on the correct way round. If the UV strip on the sail is on the starboard side then the furling line needs to exit the drum on the port side (and vice versa).  With the sail laid out on the foredeck, attach the tack of the sail to the drum and the head of the sail to the top swivel. The sheets should also be attached. Now the sail is ready to hoist which will be a lot easier to do if there are two of you, one to pull the halyard and the other to feed the sail carefully into the feeder in the luff foil. The person winding the halyard should pay careful attention to what is happening to the sail as it goes through the feeder in order to stop winding if there is any hint of a snag, this is the most likely cause of any damage. Once the sail is fully up take care not to over tension the halyard, there should be just sufficient tension to remove the wrinkles in the luff of the sail without the luff of the sail appearing taut. Then furl the sail away, double check that the UV strip is on the correct side and you should be set.

Top Tip: It will be a lot easier to bend your genoa on when there isn’t too much wind. This also helps to minimise the risk of damaging the sail as you hoist it. You will also find it easier to do if the wind is well forward of the beam. 

Friday, 30 October 2015

Winter Sail Care

Winterising Sails

As we approach the time of the year when most people are thinking about laying-up their boats for the winter it is important to give some thought to your sails. All too often we see furling genoas being left up all winter whilst the boat is ashore; the same goes for mainsails that are left on underneath their sail covers. This of course means that the sails are at the mercy of the elements for extended periods of time; not only that but the tightly bound and folded sails combined with a damp salty environment become perfect breeding grounds for mould and mildew. We strongly recommend therefore that if the boat is out of use for any period of time, especially over what can be a long and harsh winter at the very least they should be unbent and stored somewhere dry. If you are in a position to rinse and dry the sails yourself and inspect them closely prior to folding them away that’s great but if not we are happy to take care of the whole process for you.

Sail repairs and service by professionals


Regular maintenance of your sails by skilled sailmakers can significantly enhance their working life, saving money for the owner and ensuring reliability when it is needed most. Sails operate in a hostile environment where sail and pollutants can cause serious damage to even the best kept sails. Similarly, constant wear & tear requires careful repair and maintenance with an end of season overhaul being essential for the longevity of your sail wardrobe. It is important that any damage, no matter how small is repaired as quickly as possible in order to prevent further damage occurring.

Recuts and retrofits

A simple recut can improve shape and give a new lease of life to a ‘tired’ sail. With improved shape comes improved performance and handling, something that is well worth thinking about whilst the sail is off the boat anyway. Retrofit extras include UV protection, luff flatteners for shape retention when genoas are partially furled, changing from hanks to luff foils, altering batten configurations, adding reefs to mainsails etc.

Sail Laundry

OneSails recommend that any sails that are salty or damp get sent to a sail laundry prior to winter storage. The laundry process will remove any salt and any other airborne pollutants which may harm the sails if left for any period of time. This in turn helps to prolong the overall life of the sail. It also has the added benefit of making the sails easier to work on if any service work is required, and means that they will be dry when they are put away for the winter. If they are put away whilst damp, they are more likely to attract mould or mildew and will not be in a pleasant state when you come to bend them back on next season.

The specialist sail laundries are essentially large warehouse type buildings. The sails are cleaned by a variety of processes. A few older sails that have either gone soft with age or which have a soft feel by design get washed in large industrial washing machines. There is very little (if any) in the way of detergents or bleaches that gets added at this stage, the sails are simply rinsed to remove any salt. The vast majority of sails and in particular racing sails don’t go into the machines. They are laid flat on a smooth concrete floor and hosed down with fresh water from a pressure washer with a special attachment. Whilst the sail is on the floor any spot cleaning is done to remove any green algae, mildew, grease etc. At this stage some chemicals such as mild detergent solutions will be used where necessary. If chemicals have been used, the sails are then rinsed again. Once the sails have been cleaned they are then hung up to dry before being folded and returned to the sailmaker.

Whilst we highly recommend sail laundry for any sails that are being stored for any length of time, the process does have certain limitations. Although the sails will be returned from the laundry dry, salt free and in an ideal state to be worked on or stored, the process is not a cure all that will leave the sails looking ‘as good as new’. Stains such as mildew, grease and rust may be removed if they are treated straight away but will stain the sail permanently if left for any period of time. Other typical stains are from diesel or machine oil. These cannot be removed fully and will always leave a stain though laundering them will remove any smell and surface residue. It should also be noted that there is no guarantee that stains including mildew, mould or rust will be removed during the laundry process.


At OneSails GBR we are pleased to be able to offer a full range of sail repair and maintenance services, please feel free to contact us to see what we can do for you and how we can help to extend the life of your sails. 

Thursday, 16 April 2015

OneSails GBR Racing Spinnakers

The sail that is undergoing the most significant development today is the spinnaker. With the help of better fabrics and ever improving sailmaking technology, spinnakers are more efficient both downwind and also closer to the wind with angles as close as 45° apparent being possible in some cases.

The optimisation of a particular spinnaker or inventory is as much to do with subtleties in shaping as it is for overall area. OneSails make a broad range of high performance spinnakers for racing boats, symmetric and asymmetric and it is important for the owner that every sail is customised for a particular boat with specific angles and windspeeds in mind in order to give truly superior performance.

It wasn’t that long ago that a typical 3 sail spinnaker inventory consisted of a ‘light runner’ (0.5oz), an ‘A/P’ (0.75oz) and a small flat ‘heavy’ (1.5oz). The cloth weights that were used to describe these sails bore little resemblance to the actual weights. Nowadays many more cloth weights are available with perhaps as many as 10 different weights available between 0.4oz and 1.5oz. The cloths are also available in different styles each of which will be more or less appropriate to a given end use.

Towards the end of the 1990’s many boats began replacing their traditional symmetric flat heavy spinnakers with ‘mini reacher’ asymmetrics, more commonly known as A5’s. These quickly developed a reputation as a real utility sail and were able to point higher than the other symmetrics in light airs, were better at beam reaching in moderate airs and could still be flown off a conventional pole as a ‘chicken chute’ in heavier airs. Since then asymmetric development in particular has progressed rapidly and nowadays it is commonplace for most symmetrically rigged boats to also carry an asymmetric or two to cater for particular conditions.

In recent seasons Code Zero’s have become very popular especially on the more modern boats that carry relatively small non-overlapping headsails. These boats are often underpowered in lighter airs and on beam reaches that are too close to fly a conventional chute. Here the Code Zero comes into its own; in very light airs, 4-5 kts TWS for example, a boat with a Code Zero will point virtually as high as a boat with a conventional headsail but with much more area and a far better VMG. As with the A5 mentioned above, the Code Zero is also very useful at broader angles in more moderate airs when the boat would be over pressed when flying a full sized spinnaker.


The graphics below provide an indication as to how various spinnakers might fit into a particular inventory. Bear in mind that these graphics are a guide only but nonetheless provide an indication as to which sails might be used to cover a given range of conditions and angles. Clearly a smaller inventory than those shown would either leave more gaps or else mean that the remaining sails in the inventory are having to do more work or are less than optimal. For example, removing the S1.5 from the symmetric inventory doesn’t necessarily mean that the S2 can’t cover the gap it would leave but it wouldn’t do as good a job. On the other hand, if you want to sail at a TWA of 70° in 4kts TWS your only chance is to fly a Code Zero, the other spinnakers simply won’t get you there! It is also possible of course to have a mixture of symmetrics and asymmetrics onboard in order to cover all the bases. At OneSails our design teams have experience of designing custom sails for boats ranging from America’s Cup to the smallest of One-Designs and it is this breadth of experience that means that we can offer you the right advice and make sure that you get the right sails for your boat and your specific needs. Please don’t hesitate to contact us to discuss all your downwind requirements.

 Spinnaker nomenclature:

Symmetrics
S1 - Light Reacher
S1.5 - Light Runner
S2 - Medium Runner
S4 - Heavy Runner
S6 - Reduced Area Runner

Note: Odd numbers are reachers, even numbers are runners


Asymmetrics
CZ - Tight Reacher
A1 - Light Reacher
A1.5 - Light Runner
A2 - Medium Runner
A3 - Medium Reacher
A4 - Heavy Runner
A5 - Mini (reduced area) Reacher